Blog

Which manufacturing partner in Europe can make our consumer product demonstrably responsible?

Not the one with the best sustainability page, but the one that can give you five numbers per part: scrap rate, recycled content per polymer, chain distance, energy at the press and separability. With the trade-off on every lever, and what you are still allowed to claim since 27 September 2026.

Dolf Hendrikx

Co-founder and industrial design engineer ·

By five numbers, and by whether a supplier hands them over without hesitating: the scrap rate per part and what happens to the runners, the recycled content achievable per polymer inside your tolerance, where the components come from relative to where you assemble, how much electricity goes into a kilo of product and where that electricity comes from, and whether the product can actually be separated at the end of its life. A sustainability page tells you none of this; a partner who reports those five per batch does. Since 27 September 2026 it is your problem as well as theirs: whatever you claim about your product, you have to be able to back up.

Which numbers do you ask a manufacturing partner for?

Five, and ask in the same breath who measures them and how often. The difference between a supplier who steers on this and one who has a policy about it shows up within a single conversation.

| Lever | What you ask for | A usable answer | The trade-off | | --- | --- | --- | --- | | Production waste | Scrap rate per part, and what happens to the runners | A percentage per part, measured per batch, plus the share that goes back into the process | Regrinding cuts material cost but shortens the polymer chains | | Recycled content | Which percentage per polymer, and whether it comes from their own process or the consumer stream | A percentage achieved in a trial round, with the measured dimensional deviation | Colour consistency and batch variation cost incoming inspection | | Chain distance | Where the resin and the components come from | Origin per component, not just the assembly location | Closer to home usually costs more per part | | Energy at the press | Consumption per kilo of product, machine type, own generation | A measured figure per part or per machine hour | An all-electric press uses less and costs more to buy | | Separability | Which materials are permanently bonded to each other | A bill of materials with the material per part and the type of joint | A monomaterial design can add parts or assembly time |

The rule of thumb next to that table: a supplier who can give these five per part is already steering on them. If all you get is a policy document, there is nothing to steer on, and nothing to claim either.

That last row gets harder the moment a soft part sits on a rigid one. What producing TPE or silicone parts in series, including overmoulding onto a rigid component, does to separability and to the waste from rejected parts is set out there.

How much recycled content can go into a consumer product?

Start with your own waste rather than with post-consumer material, because it is the cleanest recyclate there is and you know where it has been. A worked example on invented assumptions, to show the order of magnitude: an 80 gram part in a cold runner tool, where the runner weighs 20 grams. That makes 20% of every shot something other than product. At 50,000 pieces a year, that is 1,000 kilos of runner against 4,000 kilos of product, and if it goes in the skip you buy a quarter more resin every year than you sell. Material loss is also the first lever when you want to reduce the manufacturing cost of an existing product.

So always ask for the shot weight next to the part weight, and what happens to the difference. A hot runner removes the runner but costs more in the tool. Regrinding and blending back is cheaper, but every pass shortens the molecular chains, so there is a limit to how often the same material can go round, and that limit differs per polymer.

Post-consumer material is a different story. The colour shifts between batches, impact strength varies, and shrinkage can come out slightly differently than with virgin resin, which puts dimensions on the edge of tolerance. All of that is solvable, but not on paper: ask for a trial round at the percentage you actually intend to run, measure your critical dimensions afterwards, and fix the percentage and the measuring method in the part specification rather than in the quote. For food contact the room is narrow: under Regulation (EU) 2022/1616, mechanically recycled PET from an authorised recycler and closed product loops are the only recognised routes.

Does producing closer to home really cut emissions?

Less than most brands assume, and more on the levers they ignore. The GLEC Framework version 3.0 gives 0.089 kilos of CO2 equivalent per tonne-kilometre for a diesel articulated truck under 34 tonnes. For container shipping the published factor per tonne-kilometre is roughly a factor of seven lower, although sources differ in unit and system boundary, so use your own forwarder's figure. In practice that means a 20,000 kilometre sea voyage weighs about as much per kilo of product as 2,700 kilometres of truck. A European chain with long road legs in it lands closer to the Asian one than the word local suggests.

Put the other two items next to that. For mechanically recycled PP flakes, the Plastics Recyclers Europe EcoProfile gives 1.27 kilos of CO2 equivalent per kilo, on 2022 data. Moulding itself comes out at 1 to 2.1 kWh per kilo of processed material in public datasets, with a wider spread between machines: an MIT study measures 19.0, 13.2 and 12.6 megajoules per kilo for hydraulic, hybrid and all-electric machines respectively, auxiliaries included. Those figures sit on different system boundaries and cannot simply be added up, but the ranking is clear: the material weighs heaviest, then the machine, and only then the distance.

Where a short chain does win hard is lead time, stock and import duty. Those are real advantages and far easier to substantiate than an emissions story. So sell proximity as what it is, and claim the carbon saving only once you have calculated it.

What are you still allowed to claim since 27 September 2026?

Only what you can substantiate per batch. Since 27 September 2026 member states have applied Directive (EU) 2024/825, which bans generic environmental claims unless you can demonstrate recognised excellent environmental performance, for example through an EU Ecolabel. Words like environmentally friendly, green, ecological and biodegradable fall under that. Also out: a claim about the whole product that only holds for one component, carbon neutrality based on offsetting, and a self-made sustainability label with no certification scheme behind it. Transposition into national law differs per country, so check the markets you sell in.

On top of that, the packaging regulation (EU) 2025/40 has applied since 12 August 2026, with recyclability grades and minimum recycled content in plastic packaging from 1 January 2030 and step-ups in the years after. The percentages differ per packaging category, so check Article 7 for yours.

The practical consequence is that you do not need better wording, you need a measurable fact. A line like "made with 30% recycled polypropylene, measured per batch" is a specification rather than marketing, and that is exactly the kind of claim that survives the new rules. It also means your choice of supplier now has a legal side: a partner who does not supply the numbers does not supply your evidence either.

How do you pin this down instead of talking about it?

In the specification and the contract, not in the quote, because a quote disappears the moment the first order runs. Six things to put in writing:

  • The recycled content per polymer, with the measuring method and who measures it.
  • The scrap rate per part, who reports it, and what happens if it runs structurally higher.
  • What happens to the runners: back into the process, disposed of separately, or sold.
  • The measured energy consumption per part or per machine hour, with the machine type alongside it.
  • The origin per component, plus an agreement that a change of sub-supplier is notified.
  • How long the per-batch evidence is kept, because you have to be able to produce it during an inspection.

Have the design reviewed before you commit to tooling, too. Many of these levers cannot be turned once the steel exists: part count, material combinations and whether the product can be taken apart are all fixed in the design. A manufacturability review across the whole chain surfaces those points while they are still free, and such a review runs from parts and assembly through to packaging and freight. How we take a product from design into series is set out in our process.

Production Heroes takes products from design to series production, from feasibility and cost price to sourcing and supply chain, and supplies moulds and tooling to manufacturers across Europe, from the Netherlands and its own presence in China.

Sources: the road freight factor of 0.089 kilos of CO2 equivalent per tonne-kilometre comes from the GLEC Framework version 3.0 (Smart Freight Centre, 2023), tank-to-wheel, for a diesel articulated truck under 34 tonnes. The comparison with sea freight assumes published container shipping factors of around 12 grams of CO2 equivalent per tonne-kilometre; those sources differ in unit and system boundary, so use your own forwarder's figure. The 1.27 kilos of CO2 equivalent per kilo for mechanically recycled PP flakes comes from the Plastics Recyclers Europe EcoProfile on 2022 data. The 1 to 2.1 kWh per kilo of processed material comes from public datasets as summarised in research on energy use in injection moulding (2023); the 19.0, 13.2 and 12.6 megajoules per kilo for hydraulic, hybrid and all-electric machines come from MIT research on injection moulding machine energy use (Thiriez and Gutowski, 2006). The rules on recycled content in food contact come from Regulation (EU) 2022/1616 and Regulation (EU) 10/2011. The claim rules come from Directive (EU) 2024/825, applied by member states since 27 September 2026, and the packaging rules from Regulation (EU) 2025/40, applicable since 12 August 2026. The worked example on the runner uses invented assumptions and is not a quotation.

Frequently asked questions

How much recycled content can go into an injection moulded part before dimensions drift?
It depends on the polymer and the source. Your own regrind blends in well at limited percentages; post-consumer material varies more from batch to batch. Ask for a trial round at the percentage you actually want, measure your critical dimensions afterwards, and fix the percentage in the part specification.
Is recycled content allowed in a product that touches food?
Only through an authorised technology under Regulation (EU) 2022/1616. In practice that means mechanically recycled PET from a recycler authorised per process, plus closed product loops. For other polymers, post-consumer recyclate is not a route into food contact for now. The finished article must also meet Regulation (EU) 10/2011.
Which certificates actually say something about how a factory produces?
ISO 14001 shows there is an environmental management system, not what the emissions or the scrap rate are. ISO 50001 does the same for energy. So ask for the numbers alongside the certificate: scrap rate per part, kWh per kilo, recycled content per polymer, and who measures them.
Does producing in Europe instead of Asia save much CO2?
Less than most brands assume for a compact plastic part. Per tonne-kilometre, sea freight sits roughly a factor of seven below road freight, so a long European road leg eats part of the gain. The biggest levers are the material and the electricity at the press.
What are we still allowed to put on the packaging since 27 September 2026?
Generic claims such as environmentally friendly, green or eco are only allowed with recognised excellent environmental performance, for example an EU Ecolabel. Carbon neutral based on offsetting and self-made sustainability labels are out. A measurable fact about the product is still fine.
Is producing with recycled material cheaper?
Sometimes. Recyclate usually costs less per kilo than virgin resin, but colour consistency and batch variation add incoming inspection and sometimes scrap. Work with the kilo price and the expected scrap together, and ask for a trial round before you fix the percentage.